Save Gas Digital Power Plus

Product Feature

A) The POWER PLUS (CN-P700) is stabilizer device of automotive electric power source which able to supply electric power rapidly faster than battery when instant voltage emitting (peak output) is required in driving, by achieving instant charging/discharging effect through the direct charging/discharging of electric charge into high power, high capacity condenser, by monitoring and deciding with CPU the automotive voltage which may change based on driving condition and precise controlling through using condenser's property which breaks and stabilizes noise.

B) Important factors of POWER PLUS (CN-P700) are ; temperature-compensation typed CPU which sustains maximum performance even in engine room's high temperature; it is designed as high speed-large-capacity FET(Field Effect Transistor) so that it can charge/discharge to the condenser rapidly upon CPU command; it is also designed for the condenser to perform its optimizing function under any cruel conditions.; and convenience and beauty are considered in design by mounting red led which indicates the normal operating status of CPU, green for charge/discharge and blue for breaks noise in relatively high voltage condition and for charge timing.

C) Especially, the CPU which can operate in the range of -40°C ~+125°C sustains optimum automotive condition not only in the high temperature of engine room by the driving condition, but also starting in cold winter season. We maximized its efficiency in order that CPU can monitor the voltage change in real time and decide so that FET can control the timing of charge/discharge of condenser rapidly.

D) By applying PWM(Plus Width Modulation), voltage can be controlled precisely by duty ratio so that so that it controls to charge more when voltage is low, less when high and to break noise, and stabilize voltage efficiently avoiding unnecessary discharge of the electric charge charged in the super condenser.

E) High performance heat-resistant condenser applied to POWER PLUS (CN-P700) is designed to perform excellently for its durability and capability of charge/discharge in high temperature, to break reverse current and noise, to charge under CPU control when voltage increases instantly and to maintain applied voltage by discharging charged electric charge in voltage drop.

Therefore, it is designed to improve the respondence of ECU output part such as stable and powerful ignition, increase of explosive power and injector, and to maintain output close to the automotive original maximum output by breaking noise basically in electric power source and input part, by cutting off reply-voltage from all electric power sources including engine ignition coil and by supplying automotive electric power with stable DC voltage, and its performance is excellent not only limited in specific RPM but from low RPM to high RPM range.

F) POWER PLUS (CN-P700) is available to apply all automobiles such as gasoline, LPG and diesel automobiles which engine performance is inefficiently due to unstable voltage, relaxes fine impact of generator by increase of respondence speed between ignition coil part and injector, and it secures high output and gas mileage even in cruel conditions in which driving/stopping situation °Ccurs repeatedly in down town driving.

Installation Guide

• Park the car safely in flat place, draw out key and make sure to hand break.
  
• Uncover the "-" terminal cap of battery, afterward unscrew the nut of "-" terminal.
  
• Connect the "-" (black) terminal of POWER PLUS to "-" terminal of battery, and screw the nut.
  
• Uncover the "+" terminal cap of battery, afterward unscrew the nut of "+" terminal.
  
• Connect the "+" (red) terminal of POWER PLUS(CN-P700) to "+" terminal of battery, and screw the nut.
  
• It may spark but don't worry because it is normal for charging the condenser.
  
• After completion of wiring, check if red led is on.
  
• If red led is not on, disconnect the "+" (red) terminal of POWER PLUS and battery's "+" terminal, and reconnect them after 10 minutes. (This is for resetting CPU.)
  
• Before fixing the product, close down the bonnet slowly and make sure if the product contacts with the inside of bonnet, surely.
  
• When it is confirmed that the product does not contact with the bonnet, then take off the protection tapes, clean the dust on the battery top and install the product on top of the battery.
  
• If the product contacts with bonnet, install the product on the side of battery or on other place.
  
• After engine start, and when generate begins to work, red LED turns on with green and blue LEDs in accordance with charge/discharge status of condenser.
  
• Once installation is completed, start engine and experience the outstanding effect of POWER PLUS (CN-P700) by yourself.